Aqua Products Pool Cleaner Troubleshooting Guide download pdf (Page 9)

Up & Down

arrow buttons

Red “ON”

LED

LED Time

Display

Green C-RUN

LED

Continuous

Run (C-RUN)

Button

Continuous

Run (C-RUN)

Button

RESET button

RESET

C-RUN

SECONDS

WARNING! Set the operating mode for your cleaner after the cleaner has been placed in the pool, the Floating

Cable from the cleaner has been plugged in to the Power Supply and the Power Supply has been plugged into

a GFCI/R.C.D. protected electrical outlet.

WARNING! The Power Supply should be placed in a sheltered area, at least 12 feet / 4 meters away from the

pool. While the Power Supply is weather-resistant, it is not waterproof and therefore it should be placed in an

elevated, sheltered area where it will not sit in rain or puddles of water!

SETTING THE FORWARDS / REVERSE TIMER

If your cleaner’s Power Supply features an adjustable Timer (Dial

or Digital), you can control the length of the forwards / reverse

movement time of your cleaner by using the control pad on the

Power Supply.

TIMED OPERATION: SET IT AND FORGET IT

The optimal amount of time to set your cleaner’s movements for is

the amount of time it takes your cleaner to move from the furthest

point of one side of the pool, where it can no longer move forwards,

to the closest point where it can no longer reverse, and rest there

for several seconds before reversing. Once you have set the it, you

can forget it, from here on you can forget it as your Power Supply

will recall this set time each time you turn it ON.

Digital Timers: Press the Up facing Arrow Button once for each

additional second of movement you desire (up to 90 seconds) or

the Down facing Button for less seconds (down to one second).

Dial Timers: Rotate the Dial Timer clockwise to increase the

amount of time your cleaner will move (up to 60 or 90 seconds

depending on your model) and counterclockwise to reduce the

number of seconds.

NOTE: As your cleaner’s internal Filter becomes saturated with dirt

both large and invisible to the naked eye the amount of ﬂow coming

through it will reduced reducing its jet propulsion ﬂow and your

cleaner will move more slowly taking longer time to cross the pool.

By the end of its cleaning cycle it may only spend about one second

each time it reaches the furthest point.

NOTE: You may add or subtract seconds while your cleaner is operating

and this new time will be set and recalled with each subsequent use.

IMPORTANT: In “External Timer” mode, the Safety Reset button feature becomes inactive and can not

protect your cleaner.

Safety

Reset

Button

Dial Timer

Display

STEP 3

WARNING! In “Continuous Run” mode, the Safety Reset button feature becomes inactive and can not protect

your cleaner from accidental “out of water” start up! Therefore, it is imperative that you always unplug the

Floating Cable from its Power Supply when removing your cleaner from the pool!

WARNING! Set the operating mode for your cleaner after the cleaner has been placed in the pool, the Floating

Cable from the cleaner has been plugged in to the Power Supply and the Power Supply has been plugged into a

GFCI/R.C.D. protected electrical outlet!

Continuous Run Operation (C-RUN)

Continuous Run mode means that your cleaner will operate continuously until you physically press the ON / OFF Switch to OFF.

After pressing OFF, to restart its operation again, you must physically press the Power Supply Power Switch back to ON.

This Continuous Run (C-RUN) feature is only applicable to models with Digital Timers.

KNOWING / USING MODEL FEATURES

Digital Timers

1. Turn the Main Power ON / OFF Switch to “ON.

2. Press the “C-Run” (Continuous Run) button until it is lit. Your cleaner is now set to Continuous Run mode.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Aqua Products Pool Cleaner Troubleshooting Guide Page 9

Comments to this Manuals

Related products and manuals for Above ground pool accessories Aqua Products Pool Cleaner