Aqua Products Pool Cleaner Troubleshooting Guide download pdf (Page 8)

QUICK SETUP INSTRUCTIONS

STEP 1

LOCATION, LOCATION, LOCATION OF YOUR POWER SUPPLY

1. They say location is one of the most important factors, and in the case of your Power Supply, they are right. Place the Power

Supply in a dry, sheltered area at least 12 feet / 4 meters away from the pool. Since the Power Supply is water resistant, not

water proof, it should be placed in an elevated dry area where it will it will be sheltered from water and rain.

2. Plug the Power Supply Cord into a standard Ground Fault Circuit Interrupted (GFCI) / Residual Current Device (R.C.D.)

protected outlet. If a protected outlet is not close enough, then a proper outdoor grounded extension cord may be used to

connect to the nearest grounded outlet as indicated above. Remember to always keep the Power Supply at least 12 feet / 4

meters away from the pool.

STEP 2

PLACING YOUR CLEANER IN THE POOL

With the Power Supply ON/OFF Switch in the OFF position, plug the Floating Cable into the Power Supply Socket.

2. If your cleaner does NOT have a Mechanical Wedge Turning System and / or requires the Locking Pin (see page 4), insert the

Locking Pin at this time.

3. Holding your cleaner ﬁrmly by its Handle (never by its Axle or Floating Cable) with a ﬁnger pressed on the Locking Pin (if Locking

Pin is needed), place your cleaner in the pool upside down, gently tilting it side to side to allow any trapped air to escape. While

still submersed, with the air removed, turn your cleaner right side up and allow your cleaner to sink to the pool bottom, with its

Wheels down.

NOTE: If your cleaner does not sink it is because air is still trapped inside. Repeat Step 2.

4. If your pool is elongated (rectangular, oval, etc.), insert your cleaner at the middle of the pool’s length and uncoil the Floating Cable

that extends from the cleaner’s body and spread it evenly over the pool water surface allowing adequate Cable length to reach the

entire pool. Excess Cable in pool may result in unnecessary coiling or tangling.

WARNING! The Power Supply may only be connected to a Ground Fault Circuit Interrupter (GFCI) / Residual

Current Device (R.C.D) to protect your electric outlet and to prevent from possible electrical shock!

WARNING! Set the operating mode for your cleaner after the cleaner has been placed in the pool, the Floating

Cable from the cleaner has been plugged in to the Power Supply and the Power Supply has been plugged into a

GFCI / R.C.D. protected 115v grounded electrical outlet!

CAUTION! Always hold and remove your cleaner from the pool by its Handle only - never by its Axle or Floating

Cable. Doing so will result in unnecessary costly repairs.

WARNING! The Power Supply should be placed in a sheltered area, at least 12 feet / 4 meters away from the pool!

While the Power Supply is weather-resistant, it is not water-proof and therefore should be placed in an elevated,

sheltered area where it will not sit in water or rain!

Never allow anyone to swim in the pool while the cleaner is in the pool!

CAUTION! Never operate your cleaner when it is not totally submersed in the pool water! Doing so may cause

severe damage to motor and require costly repairs!

TIP! For optimum cleaning performance locate the Power Supply at the mid-point of your pool’s longest side. This will

allow your cleaner to make the best use of its Floating Cable length without using excess Cable, which could result in it

unnecessarily twisting or kinking. Excess Cable should be kept coiled outside the pool near the Power Supply.

12ft. / 4m

Power supply

Cleaner

Long side

of pool

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Aqua Products Pool Cleaner Troubleshooting Guide Page 8

Comments to this Manuals

Related products and manuals for Above ground pool accessories Aqua Products Pool Cleaner